Tianjin Weilei Technology Ltd.

Homepage:Login:Register:Soul:Top Host

Forum style

Interface Style:

Total 1442,Total 29 pages

[1][>>]

programming the PIC18F6680

chz132

Hello everyone, I"m from Mexico.

I have a problem trying to program the PIC18F6680 with the Wellon programmer model VP898. The first is that when trying to read the PIC using the ISP connection, the computer does not detect it. I"m not sure if this is due to the lack of drivers for the Wellon, since it only happens with the ISP port. However, when I read other PICs using the 48-pin port, they work without problems.

Has anyone had this problem or knows how to fix it?

Reply the message

[ Posted:2024-12-20 02:41:32 ]

comom usar lel wellon con el pic18f6680

chz132

Hi, I"m new to programming the PIC18F6680 and using the Wellon VP898 programmer. When I try to load or modify a file, I get an error. I think it could be because of the bit configuration (fuses), but I don"t know if it"s done in the Wellon software or in MPLAB X IDE, where the program is developed. Could anyone with experience with this programmer guide me on how to use it correctly with the PIC18F6680? Thanks!

Reply the message

[ Posted:2024-12-19 23:10:51 ]

WL-EBGA64-640C3

transiente register

Good morning everyone. I"m from Brazil.
I"m looking for the WL-EBGA64-640C3 adapter but I can"t find it anywhere.
I want to read and write to the RC28F160CEBE chip.
Does anyone know where I can find this adapter or a replacement?
My programmer is the VP980.
Thank you.

Last post : Re:WL-EBGA64-640C3	Reply: transiente
Thanks for the help

All replies (2)

[ Posted:2024-11-27 19:39:09 ]

VP598 not working

oguz

I"ve just bought that VP598.
Installed drivers. Device shown in software too.

unplug it. Then plugged it again.

No more leds.

Leds go for half second lit, and no response.

What is the problem?

https://youtu.be/6KtWWrK5Ha8

[ The message is modified by oguz ]

Last post : Re:VP598 not working	Reply: oguz
Problem solved by Weilei.

All replies (1)

[ Posted:2024-11-23 06:37:30 ]

Adapters

QazQaz

Hi,
I need adapter connections:
1. dsPIC33FJ256MC510A-PT　adapter WL-FQFP100-M002
2. PIC24HJ128GP506A　　　 adapter WL-TQFP64-M065

Thank you
Ed

Last post : Re:Adapters Reply: lxl Host

please contact with us　weilong@weilei.com.cn

All replies (3)

[ Posted:2024-09-23 18:46:14 ]

WL-PQFP52-M517

Valeron

Hi! Adapter information required for R5F21258SNFP .It is not available for sale.I need a wiring diagram.

Last post : Re:WL-PQFP52-M517	Reply: lxl
you can buy the adapters. you cannot use self made adapter

All replies (1)

[ Posted:2024-09-24 16:21:29 ]

WL-PQFP64-M355

Valeron

Hi! Adapter information required for R5F100LEAFA .It is not available for sale.I need a wiring diagram.

Last post : Re:WL-PQFP64-M355	Reply: lxl
you can buy the adapters. you cannot use self made adapter

All replies (1)

[ Posted:2024-09-24 16:18:31 ]

how to program PIC16F1508 with VP-ISP1

Java_Raja

Hi, everybody
How to add a new item to list of programmable devices?
I want to program PIC16F1508 MCU. I have a VP-ISP1 programmer. I can"t find this device at "SELECT" menu of programmer software. My programmer software version is: 4.2.0 (12/8/2009).

[ The message is modified by Java_Raja ]

Last post : Re:how to program PIC16F1508	Reply: lxl
Sorry, the programmer have stop produce and its software have stop update.

All replies (1)

[ Posted:2024-09-15 16:57:30 ]

buffer editor Windows

Bin10

Hi, please info.
Is it possible to enlarge the "BUFFER EDITOR" window in the Wellon programmer program?
By default it is very small.
Thanks.

Last post : Re:buffer editor Windows	Reply: Valeron
To enlarge the window, you need to click on the square in the upper right corner

All replies (2)

[ Posted:2024-09-02 17:16:55 ]

WL-TQFP64-P058 diagram

Lukasz

I need connection diagram WL-TQFP64-P058

Last post : Re:WL-TQFP64-P058 diagram	Reply: lxl
you need buy the adapter.

All replies (1)

[ Posted:2024-08-20 19:44:16 ]

ST72F problem　connections v4.7.4

Valeron

In the program ST72F325J7T6, according to the information of the WL-ISP-U001 adapter, the VDD power supply is connected to pin 31,and according to the datasheet to pin 32.VSS to pin 32, and according to the datasheet to pin 33.

Last post : Re:ST72F problem　connections v4.7.4	Reply: lxl
The isp mode involves the user circuit, which is affected by many factors and needs to be discussed by the user himself. We only test the case that the chip is not connected to other circuits.

All replies (1)

[ Posted:2024-07-29 03:42:23 ]

vp990 trouble

js23

VP990 ver 4.2.0　 code 0163835C11000009
What is it?

Last post : Re:vp990 trouble	Reply: lxl
please use wellon software ver. 4.6.6

All replies (1)

[ Posted:2024-06-26 16:50:36 ]

Help with device 12f519 soic

kyo

Hello in version 4,7,1 the device 12f519 it´s ok
But in mew version does not work.
Please can you check
Thank you

Reply the message

[ Posted:2024-06-12 04:00:11 ]

Winbond W25Q64JW 1.8v SPI flash

cwispy

Can you please add support for the Winbond W25Q64JW 1.8v SPI flash devices?

Reply the message

[ Posted:2024-06-08 02:12:04 ]

PSD3XX, VP998

Lukasz

How programming PSD301,302 or PSD311. I tried many times and nothing. ERROR. Read is possible, only CRC is litle diferent from write on chip. Help me pleas.

Last post : Re:PSD3XX, VP998	Reply: Lukasz
I have two different type chip, UV reset and without. Only read. If i click on to SECURE,i have text Secure OK!!

All replies (2)

[ Posted:2024-06-01 13:22:25 ]

GD 25LR128DSIG

marcinm

Hi. Please add support of GigaDevice 25LR128DSIG to VP998.

Reply the message

[ Posted:2024-05-23 23:33:00 ]

VP596 update Ver: 4.7.1

mk2power

Hi,
You say that the update Ver: 4.7.1 work with VP596 (

http://www.weilei.com/dow.asp ) but after install it, the model VP596 are not listed.
It"s mistake ?
best regards

Last post : Re:VP596 update Ver: 4.7.1	Reply: lxl
the list is just advertising

All replies (1)

[ Posted:2024-04-10 17:03:33 ]

VP-480 Windows 7 (64 bit)

twanger

Hi!

I upgraded to Windows 7 (64 bit) and would like to use my VP-480.
What can I do? Where can I get drivers?

Best regards!

Last post : Re:VP-480 Windows 7 (64 bit) Reply: lxl Host

http://www.weilei.com/rj/Disk64_434.exe

All replies (4)

[ Posted:2010-10-19 01:44:05 ]

ESMT F50L1G41LB

mateusz12bob register

Good morning,

Can you add another chip (ESMT F50L1G41LB) to be operated by the VP998 programmer?

Regards
Matthew

Last post : Re:ESMT F50L1G41LB Reply: lxl Host

please download new software

All replies (1)

[ Posted:2024-03-26 06:33:45 ]

R5F21258SN error final addres

Valeron

Hi! The program contains an error in reading and writing the address map of the microcontroller R5F21258SN . The final address of the dump PROGRAM ROM should be located according to the map in line 13FFFH .How can I fix this in the program ?

Last post : Re:R5F21258SN error final addres	Reply: Valeron
Downloaded a new program. The issue has been resolved. Thank you for efficiency !

All replies (2)

[ Posted:2024-03-25 04:10:30 ]

Wellon VP896

Ibrahim

Hello,
I have a wellon VP896 programmer, I want a chip MX IC 25L12872F M2I flash, this chip is not in your archive, please help me to program this chip, please trouble your archive with this chip.

Thank you

Greetings
I. Uslu

Last post : Re:Wellon VP896 Reply: lxl Host

please send error photo to weilong@weilei.com.cn

All replies (6)

[ Posted:2024-03-07 19:27:19 ]

Problem with read memory MX30LF4G28AD-TI

netcomers

Hello,

I have a problem reading memory from MACRONIX MX30LF4G28AD-TI chip. Each time there are differences in the read data.

I use the default settings in "Modify Algorithm Parameters". VCC: 3.00V, tPw 200uS, Page: 2160 and Retry: 25.

Enabling the "Slow Program/Read" option does not help.

Windows 11, Wellon VP998, Firmware Ver.10.0, Program Ver. 4.7.4.13.12.2023

Any suggestion?

[ The message is modified by netcomers ]

Reply the message

[ Posted:2024-03-21 20:09:59 ]

tms34010

Rework_Systems register

Hi!
tms34010fnl you can read?
I have wellon vp-996 but it has not received updates for a long time

[ The message is modified by Rework_Systems ]

Reply the message

[ Posted:2024-02-22 03:02:17 ]

VP-996 Strata Flash problem

PanPancerny register

Hi!

I am trying to program 48F4000P0ZBQ0 Strata Flash memory and only read is possible. When trying to program it, software indicates error that memory isn`t blank, even when memory contains only FF`s. I am using VP996 with firmware version 23.0. What can be wrong?

Last post : Re:VP-996 Strata Flash problem Reply: PanPancerny registered

Email sent. Thank You.

All replies (2)

[ Posted:2024-01-02 22:36:48 ]

MC80F0224Q in vp998

Valeron

Is it possible to add MC80F0224Q in vp998 list ?

Last post : Re:MC80F0224Q in vp998	Reply: lxl
sorry, We have not its programming algorithm datasheet.

All replies (1)

[ Posted:2023-12-29 15:00:10 ]

mcu not in vp998 list

fatih35m

hello
MC56F84550 is not in the mcu vp998 list, is there an urgent solution for this?
I opened two threads before, there is no answer for the same topic, what a thought, I couldn"t solve it
thanks

Last post : Re:mcu not in vp998 list	Reply: lxl
sorry, it have not program algo.

All replies (4)

[ Posted:2022-02-23 12:25:08 ]

Wellon VP 480 programmer driver

GiuseppeR. register

Did someone have the driver for Windows for this device? I lost mine CDRom with it

Thanks

Last post : Re:Wellon VP 480 programmer driver Reply: lxl Host

please down load wellon software ver 4.3.4

All replies (2)

[ Posted:2023-10-20 00:36:22 ]

Wellon Auto fault

grandziu34 register

Hallo,
After turning on the Wellon version 4.7.1 program, I get the information "Initiating. Please wait...
VCC Error!
VPP0 Error!
Programmer initiate failure!"
What is the problem? Can anyone help me how to fix this?

[ The message is modified by grandziu34 ]

Last post : Re:Wellon Auto fault	Reply: grandziu34
Wellon Auto

All replies (2)

[ Posted:2023-10-16 16:44:53 ]

ATF16V8C 5JX-PH - Error

mamejay

Hello.　I am trying to write a GAL chip ATF16V8C PLCC
I get the following

>>.Auto Program......
>>.Blank Check......
>>.Program......
>>.Verify(VCC: 5.25V) ......
>>Device Address:00000000H　Device Data:00H　Buffer Data:01H
>>Auto Program fail!
>> 38.81Sec

I have a external power supply connected.　It tried to write but the progress bar gets near the end and the write starts again.　This happens 3 times then I get the error.
Please help!

Reply the message

[ Posted:2023-09-24 14:59:18 ]

VP998 and AT93C56A

confal4444 register

Hello

I try to programm a　AT93C56A

I used the small ISP adapter supplied with the programmer. I connected each wire to the pins of the eeprom support, following the instructions. (isp　drawing)
The programmer writes that writing is ok, but when I try to read. the eeprom to check by opening the buffer, the file is blank.
I tested several new eeproms and always the same observation.

Where is my mistake?

Last post : Re:VP998 and AT93C56A Reply: Valeron registered

I think these microcircuits are better to read and write directly in the connector DIP

All replies (2)

[ Posted:2023-08-18 16:48:23 ]

STC 89c52rc

hasan

hello stc 89c52rc my programmer vp998 i can"t read it just test the programming can you help with the issue

Reply the message

[ Posted:2023-08-31 03:07:59 ]

VP390+ Read Communication Error! 0 6

Layer

Hello,

When I try to read an eprom, I get the following issue with my VP390+ and the latest version of Wellon :
"Read... Communication Error! 0 6"
USB cable is OK, everything seems OK, see the picture below.
https://image.noelshack.com/fichiers/2023/35/2/1693325903-wellon-vp390-read-error.jpg

Reply the message

[ Posted:2023-08-30 00:20:13 ]

VP998 or VP898 choice

Valeron

I want to buy wellon VP998 from aliexpress. But only Wellon VP898 is on sale. Will the program work from VP998 . On the website

http://www.weilei.com　I did not find information on VP898. In the latest version of the program, there is no choice for the programmer VP898 at startup ...

Last post : Re:VP998 or VP898 choice	Reply: confal444
I bought my vp998 from a distributor in Poland

All replies (1)

[ Posted:2023-08-05 15:15:20 ]

VP-299 read file error

vk3gm

Hi Support,

I am using a VP-299 and this unit will not read working EPROM, AM27C1024.

The following message appears while trying the read the 40 pin DIL device.

>>Programmer initiate success!
>>Note! Need AC adaptor!

Read algo file error!
>> 0.85Sec
----------------------------!

Regards
Gerald

Last post : Re:VP-299 read file error Reply: vk3gm registered

Hi Support,
By downloading latest release 25/07/2023, will this work with my existing VP299 hardware?
Regards
Gerald
VK3GM

All replies (2)

[ Posted:2023-07-24 18:07:47 ]

why the erase button is missing

amitay

Hi
I am a new user, try to erase AT29lv1024.　when i choose the device i program it, and now i want to re-program it.　but for my surprise , the erase button is grey out, and i can"t erase device or re-program it.

any idea ?

AT29lv1024 is a flash memory.

Last post : Re:why the erase button is missing Reply: lxl Host

This chip does not need to be erased before programming

All replies (1)

[ Posted:2023-07-16 13:18:19 ]

Over Current Detected

markr

I have brand new Wellon Auto. Trying to read 93C86 eeprom in circuit. I get Over Current Detected warning
I have tried modifying VCC down to 3.0v
I have older VP-390 that I have managed to read the eeprom with under Microchip 93C86 with VCC set between 4.25v - 4.5v. No Power Supply
The new Wellon Auto will only connect to PC Software with power supply connected
Is it normal for Wellon Auto to have to use power supply?
Why is it saying Over Current Detected?

Last post : Re:Over Current Detected	Reply: lxl
Wellon Auto300 need use power supply

All replies (1)

[ Posted:2023-06-27 13:19:07 ]

Wellon buffer editor

exc11

Hello. I"m new to wellon program. How to change buffer editor resolution/make text bigger? Hex values are so small that I can"t recognize them. Win10.

Last post : Re:Wellon buffer editor	Reply: lxl
sorry,cannot.

All replies (1)

[ Posted:2023-06-17 15:56:57 ]

Program pal20L8

diegojardim register

Hello, I"m new to the forum, I have a VP798 recorder, how do I read and record the PLD PAL20L8, the original is tibpal20L8, in other recorders it says that you can record and read with the gal20V8, but you can"t, it has this availability on recorder ?

Last post : Re:Program pal20L8	Reply: lxl
sorry,VP798 do not supports tibpal20L8 format file.

All replies (1)

[ Posted:2023-06-20 07:12:06 ]

Vp-890 windows 10 64bits

Bonky

Hello,
I have a vp 890 working on windows 7 but i need to go to windows 10.
What program is needed for running on w10 64bits ?
Thanks in advance.

Last post : Re:Vp-890 windows 10 64bits	Reply: lxl
after install wellon software,USB driver is c:\weilei\wellon\usbsys64\

All replies (1)

[ Posted:2023-06-14 22:21:11 ]

Dallas DS2502*3TO To92

Vasek

Hello
I can"t read eeprom ds2502 it says: Note! The device isn"t supported!
But can select chip from programator chip list
I use VP-890 a sw version 4.7.4 and firmware ver 23.0
Thanks for info
Regards Vaclav S.

Last post : Re:Dallas DS2502*3TO To92	Reply: Vasek
I have installed older version 4.6.6 and i t works.Thanks for help

All replies (2)

[ Posted:2023-06-03 00:11:23 ]

vp998 not programming xilinx cpld

rgallegos

Hello,
I"Mm trying to program xilinx xcr3032xl cpld. I get
>>.Erase......
>>Erase OK!
>>.Program......
>>.Verify......
>>Device Address:011081　 Device Data: 1　 Buffer Data: 0
>>Program fail!
>> 1.96Sec
any help appreciated

Last post : Re:vp998 not programming xilinx cpld	Reply: lxl
please send the jed file to weilong@weilei.com.cn

All replies (5)

[ Posted:2023-05-05 04:49:59 ]

82S123 series

Roger

Bom dia a todos
sou o Roger do Brasil
tenho um VP589
Na lista de componentes consta as memorias Philpps 82sXXX mais não encontro no softwere
Alguem poderia ajudarme?

Last post : Re:82S123 series	Reply: lxl
VP598 do not supports these 82sXXX

All replies (3)

[ Posted:2023-05-25 20:04:22 ]

Can not Detect AT29C040A with WL-TSOP48

Helder

I have tried so many adapters and I have the WL-TSOP48-U001 and this flash chip will not be recognized as it is in the device. Says No Device in socket.

I have placed the pin 1 of the IC where the white dot is and even used a multimeter to make sure pin 1 on the header matches the one in the socket but it never detects the IC. What adapter is made for TSOP32 with width 20mm? This one is not working nor are the generic ones either.

Last post : Re:Can not Detect AT29C040A Reply: lxl Host

programmer type? please send the error photo to weilong@weilei.com.cn

All replies (1)

[ Posted:2023-05-15 08:20:57 ]

PIC18F27K42

Radek

Hi
I have problem with programing PIC18F27K42. I can read from working chip　but i cant program new chip. I have dump with config.

Last post : Re:PIC18F27K42	Reply: Radek
i cant erase new chip (2 pcs new) >>.Erase...... >>Erase fail! >> 1,27Sec ----------------------------!

All replies (2)

[ Posted:2023-05-08 16:56:58 ]

error initialising Win10 - vp-380

Brian

I have tried all versions of install packages on Win 10 for my VP-380 and i get the following error...

>>Initiating, Please wait...

>>Programmer initiate success!

>>The programmer type error!please notice Manufacture!

the USB 64 bit driver appears to have installed correctly. Is there new HW update for this programmer i need ?

Last post : Re:error initialising Win10 - vp-380 Reply: lxl Host

please use wellon software ver. 4.3.4.

All replies (1)

[ Posted:2023-05-07 04:29:44 ]

Does VP280 supports MX25L8035 / 25V8035?

AndreyKT

It"s not clear to me if old programmer VP280 may read/write to MXIC SEPROM 25L8035 / 25V8035. Please help to understand and let me know hot to rightly put this SEPROM into programmer socket.

Last post :

Re:Does VP280 supports MX25L8035

Reply: lxl Host

please see "help"-> 4.4 Device Insertion

Normal insertion: Following the reference next to the socket, always insert the device into the bottom of the socket, oriented with the pin 1 located in the upper left corner. As follow plot.

All replies (1)

[ Posted:2023-03-15 16:02:42 ]

Error programing M27C801

Daniel2123 register

https://postimg.cc/Yhv2Q5g9

Hello, this error appeared to me the first time I tried to program a blank eprom.

What could cause the problem? all the blank memories I try to program throw the same program fail error.

thanks in advance.

Last post : Re:Error programing M27C801 Reply: lxl Host

The chip needs to be erased with an ultraviolet remover

All replies (1)

[ Posted:2023-01-22 02:36:40 ]

EEPROM 27C512 (PLCC 32PIN)

Shahmin Helmi register

hi, Wellon pls update your software. in your EEprom list thre is only for
DIP 28pin no PLCC 32pin ( example at27c512R ) . I can"t copy & program the IC. TQ