i have just bought vp-996 from TOMSAD (POLAND).

All working fine ( microship, atf, ...) but : wellon with atmel chip has problems with writing and veryfing
i can read source sprom, verivy buffer with chip (which looks OK) but get errorr after writes back ( what takes approx 30 secs - read takes 5..)

Please, advice

Last post : Re:AT45DB041D - SSU page 256 8SO ISP	Reply: lotharek
Picture sent

>>Load File OK! Time:11/07/2557 15:57:39
>> 0.02Sec

>>.Blank Check......
>>Blank Check OK!
>> 0.47Sec
----------------------------!

>>.Auto Program......
>>.Blank Check......
>>Auto Program OK!
>> 0.81Sec
----------------------------!

>>.Auto Program......
>>.Program......
>>Device Address:00000001H　Device Data:00FFH　Buffer Data:5C06H
>>Auto Program fail!
>> 0.75Sec
----------------------------!

Last post : Re:Program error for VP-490	Reply: lxl
1. please select "Device ID Check". 2. Blank Check the chip. is its ID correct? 3.if incorrect,please check the adapter or use another chip.

Thanks for your urgently reply.

Last post : Re:VP-490 Software	Reply: nipat3t
http://www.weilei.com/Disk1.zip

Can anyone help me?

tnx

Last post : Re:prog JS28F640J3D with VP-480	Reply: lxl
what question?

Regards,
Tawatchai

Last post : Re:Intel AB28F400 PSOP44	Reply: lxl
sorry,VP-390 don"t support psop44 package beause hardware.

I got an vp 590,using a tsop56 f640 adapter.i use power cable
I can readmy chip sharp lh28f160s3t l10a
But i cant erase it (no erase process on software,just written erase,blue led is blinking then after a while erase error appears)

Last post : Re:error with f640 adapter	Reply: lxl
please download new software.

Using vp590 with last software and power cable

I test ttl 74ls373 (10 new) and only got error
I test the sames ttl on older software(from cd of the vp590 box) and all are ok

Last post : Re:ttl error	Reply: Infirmier
I cant be sûre that test is OK,since vector are wrong. Ttl are OK Your software is great,no problem :-D I will check thoses ttl on older software. Thanks for your help!you"re great!

One line in vector table must be corrected as follow:

V0005 11H0110G1101H11V

Thank you

Last post : Re:cmos test 4052	Reply: lxl
thank you,the software will updated

Thanks.

Last post : Re:VP990, support KKZ06F	Reply: kruPL
Software 4.6.4(2014-06-03) (demo mode) KKZ01 - not supported in vp596/vp390/vp290 Please add support for all programmers. Thanks.

that tall .. I tell them I Wellon WL-896 with EBGA64-E138-3 .... I want to read bga gl256s90fhi01 ..
but detected Wellon WL-EBGA64-E138-3 ..

I wonder if someone can send me your file WL-EBGA64-E138-3.FIG to check whether the socket works or not ..
is testing another Wellon same error 996 and other model bga ..

if you can send me to my email or upload files to the web.

thank you very much

send WL-EBGA64-E145-1.FIG

download: http://200.55.243.142/WL-EBGA64-E145-1.FIG

Last post : Re:file WL-EBGA64-E138-3.FIG please	Reply: lxl
1.please run your teamviewer, 2.email me your teamviewer"ID and password. 3.I will remote your PC.

>>Programmer initiate success!
>>Load File OK! Time:12/12/2013 12:21:52
>> 12,92Sec

>>Man.Code:AD　 Dev. Code:F1
>>.Auto Program......
>>.Erase......
>>.Program......
>>Device Address:04308409H　Device Data:00H　Buffer Data:15H
>>Auto Program fail!
>> 252,52Sec
----------------------------!

Last post : VP890 X　H27U1G8F2	Reply: myx1
please download new software if yours is old. and click "fig" then select "hard copy(verify)" "page2112".then program. if your chip has bad block,you"d better select "hard copy(no verify)".

Does the VP-480 can work under Win7 64bit or not?
Which version of your software can support?

Last post : Re:VP-480 with Win7 64bit	Reply: lxl
please use V4.3.4 64bit version.

I have socket　Model : E145-1 - 138-3　others ..

I can read with 896 VP ISP mode? .. Connected to its pin BGA, I selected a similiar model BGA

Please send information
THZ

Last post : vp-490	Reply: myx1
you can select 8pin-ISP and link like below　or download new software later. 1--WP--C4　|　10-- 2--SI--D3　|　9--VCC--B4 3--SO--D2　|　8-- 4--CS--C2　|　7--HOLD-D4 5--GND-B3　|　6--SCK--B2

I have a Vp-990 programmer and I"m trying to dump the program content in a CPLD from Xilinx XC9572 in a PC44 package, When I read It i have no problems, but when I try to verify the buffer that contents the program i read with the program on the chip there appears mismatches and I don"t know wy, does anyone can help me?

I"m using a DIY adapter, I"ve added 100nf decoupling caps to the adapter board and the problem rests

Last post : Re:XC9572 Problems	Reply: lxl
please send the photo to weilong@weilei.com.cn

http://hackaday.com/2011/05/18/arduino-arcade-rom-dumper/

Thank you in advance!
Enzo.

Last post : Re:82s129 read support on VP390	Reply: lxl
sorry, VP-290 do not support it,please use VP996.

Problema no Programador!ID: 39FFA8340000002E

como resolvo isto ?

Last post : Re:wellon vp-390	Reply: lxl
have sent you reset software.

>>Man.Code:20　 Dev. Code:0C
>>.Erase......
>>Erase fail!
>> 14,14Sec
----------------------------!
the chip is otp ? any solution ?

thanks

Last post : Re:ST M28W320HSU @64EBGA	Reply: lxl
you need update your software.

>>Programmer trouble!ID: 012D873B150000F8

What can I do?

Last post : Re:wellon 890 Problem	Reply: lxl
Please PrintScreen on the whole interface including the error message and send it to weilong@weilei.com.cn